Why Use Gtechniq G1 ClearVision Smart Glass?
Unlike regular rain repellent coatings that adhere to the surface of the glass using relatively weak physical bonds, G1 uses a chemical bond which gives G1 unrivalled durability.
G1 ClearVision Smart Glass is extremely durable, the hydrophobic function improves wet weather visibility helping to improve safety and eye strain. It also makes removing contaminants from the glass such as ice, bugs and tree sap much easier.
G1 will only work on glass substrates and so, it will not work on modern headlight lenses which are made from polycarbonate. For these you will need to use G5 Water Repellent for Glass and Perspex.
Choose the 15ml bottle for windscreens only, but the 100ml bottle if looking to use on all of your car’s glass. G1 is supplied with G2 Residue Remover.
使用方法
使用前搖均,避免陽光直射下施工,建議使用手套;施工周邊溫度超過5度,且保持通風透氣
•①用G6(玻璃清潔劑) 和MF5(強力玻璃毛巾)清潔即將要施工的玻璃和雨刮,
•②為達到最佳效果,推薦清潔後用G4(玻璃納米拋光修復劑)配合拋光盤對玻璃進行拋光處理-打
圈塗抹直到全部覆蓋,重複以上①動作,再次清潔玻璃,直到玻璃完全乾淨,或直接跳過步驟②
•鍍晶開始,我們推薦對擋風玻璃鍍晶3層,其餘玻璃鍍晶一層
•把G1倒在AP1(護理墊)上,然後在玻璃塗抹。對於三層鍍晶,我們推薦每次施工時間間隔5分鐘,
第一層鍍晶,採用打圈方式在玻璃上塗抹,第二層鍍晶,左右來回塗抹,第三層鍍晶,上下來回塗
抹。第三層鍍晶完成後,自然滲透15分鐘
•15分鐘後,用產品自帶的G2祛除鍍晶層殘渣或模糊-把G2塗在新的護理墊上,小面積擦拭,然後立
即用MF1(超軟纖維毛巾)輕輕擦拭
• 施工完成後,重複以上①動作
• 同時我們推薦在雨刮上也塗抹G1,無需祛除殘渣
• 全部完工建議讓車停留3小時,產品達到最佳效果
注意:三層鍍晶,建議每次塗層都盡量更換新的護理墊。如果鍍晶後,雨刮出現跳動,屬於正常現象,
實際經驗90%以上的雨刮跳動會兩週後自然消失
Simple Steps To Help You Get The Best Results
-
Make sure you are working in a well ventilated area, in a temperature that is 5°c or above
-
Wear gloves and do not apply in direct sunlight
-
Clean all glass you are going to protect with G6 Perfect Glass and an MF5 Power Glass Cloth
-
For best results machine polish the glass with G4 Nano Glass Polish and a medium pad. Or alternatively, polish the glass with G4 Nano Glass Polish and a hand polishing pad. Apply a small amount and polish in a circular motion
-
Once finished, clean the glass back to a shine with G6 Perfect Glass and an MF5 or MF1 ZeroR Microfibre Buff Cloth – repeat this as many times as needed to remove all residue
-
Shake bottle well before use
-
For windscreens we recommend using 3 layers of G1, but for side and rear screens only 1 layer is needed
-
Apply a liberal amount of G1 to a AP1 Lint-Free Applicator Pad
-
Work product into the glass in a circular motion covering all of the glass, and leave to cure for 5 minutes
-
Using a new AP1 apply the same amount of product to the pad, but this time put G1 over your previous layer in a side to side motion, leave for a further 5 minutes to cure
-
Apply your third layer with the same amount of product on a AP1, however this time apply in vertical straight lines, leave to cure for 15 minutes
-
Remove cured residue, with G2 Residue Remover. Dab the G2 onto the remaining applicator and apply to a small area at a time, then buff the glass immediately with an MF1 cloth
-
Finish by cleaning the wiper blades and glass with G6 Perfect Glass and an MF5
-
We recommend you apply a layer of G1 on your wiper blades without removing residue. If wiper blades are worn they should be replaced
-
Do not expose your car to the elements for at least 12 hours
-
Store in a cool, dry place
-
Use G1 and G2 within 3 months of opening
-
There may be some wiper blade judder, in 90% of cases this will disappear within two weeks. Please take a look at our FAQ section if this problem persists