Box contains:
-30ml or 50ml HALO v2 Flexible Film Coating
-A pair of nitrile gloves
-AP2 Ultra Soft Foam Filled Applicator
-Master Instruction Leaflet
-Gtechniq window stick
HALO enhances the performance of Paint Protection Film (PPF) and vinyl. It’s a chemically bonding, ultra-dense flexible film that becomes the permanent surface of the film – protecting it from the elements a car faces on a daily basis.
The density of the coating and its low surface energy improve dirt and water repellency of PPF or vinyl. It also helps to prevent staining from dirt ingression, as well as reducing yellowing caused by UV rays.
Overall, HALO keeps the PPF looking in a much better condition and makes it much easier for people to keep their car clean following PPF/ vinyl application.
Rigorous real-world and laboratory testing has proven HALO to be compatible with all types of gloss, matte, and satin vinyl and PPF. It is also proven to work on self-healing films.
使用方法
1. 搖勻瓶子並戴上手套
2. 要應用 HALO，您的車輛必須在室內並在應用塗層後至少留在室內12 小時。 為了獲得最佳效果，良好的照明是必不可少的
3. 如果適用於以前安裝的薄膜，請使用 Gtechniq W5 通用清潔劑和 W6鐵粉去除劑清洗車輛並淨化
4. 在您的表面完全冷卻和乾燥後，將 30% 的異丙醇 (IPA) 稀釋液噴灑到 Gtechniq MF1 ZeroR 超細纖維拋光布上。 這將去除任何指紋或其他表面污染物
5. 將 HALO 均勻塗抹在塗抹墊上，然後將瓶子放在一邊
6. 使用以重疊筆觸提供的塗抹器塗抹在大約 2 英尺 x 2 英尺的區域
7. 塗裝面板後，用 MF1 布清除殘留物。 總是從比你應用的更遠的地方移除，從外到內工作
8. 塗抹後,用MF1布和以明亮但漫射的光源進行最後檢查——這將識別表面上是否有多餘的殘留物。讓塗層固化至少一小時，然後重複應用過程，使所有薄膜和乙烯基都塗上兩層 HALO
9. 一瓶未開封的 HALO 自購買之日起保質期為 12 個月
Simple Steps To Help You Get The Best Results
-
Shake bottle well and wear gloves
-
To apply HALO, your vehicle must be indoors and remain indoors, for at least 12 hours after the coating has been applied. For best results, good lighting is essential
-
If applying to previously installed film, wash and decontaminate the vehicle with Gtechniq W5 Citrus All Purpose Cleaner and W6 Iron and General Fallout Remover
-
With your surface fully cooled and dry, spray a 30% dilution of isopropyl alcohol (IPA) on to a Gtechniq MF1 ZeroR Microfibre Buff Cloth. This will remove any fingerprints or other surface contaminants ensuring you get the maximum number of chemical bonds between HALO and the film or vinyl
-
Apply HALO evenly onto the application pad and set the bottle aside
-
Apply with the applicator provided in overlapping strokes to an area roughly 2ft x 2ft.
-
After coating a panel remove residue with an MF1 cloth. Always remove from further than you have applied, working from the outside in
-
Once applied carry out a final check with an MF1 cloth and a bright but diffused light source – this will identify any excess residue left on the surface. Allow the coating to cure for at least one hour and repeat the application process so that all film and vinyl is coated with two layers of HALO
-
An unopened bottle of HALO has a 12-month shelf life from the time of purchase
-
Store in a cool/dry place, out of direct sunlight
-
If opened, use within 3 months, if unopened, use within 12 months
-
* Avoid direct application, paint or rubbers. *
